Titanium Yamaha Components
 

Titanium axles will decrease your unsuspended weight. Our axles are equal to strength to steel but the hardness is less. For this reason we recommend the application of a protective coating. In past years, Teflon or Titanium Nitride was used for the coating but does not hold up to the punishment encountered from aggressive riding. Mettec now offers an aerospace derived coating called Quadralloy. Quadralloy increases the surface hardness and reduces the wear caused by the bearing contact point on the axle surface. By increasing the surface hardness wear is reduced but not stopped. 
Yamaha R6 & R1 Front Axles

 

Mettec front axles are made with a new high strength titanium alloy with a Minimum UTS of 195,000psi (1,344MPa). Good enough for space craft and jet fighters, and is a stronger replacement than Titanium 6/4 which only has Minimum UTS 160,000psi (1103MPa). Mettec applies our proprietary hard coating to the outside surface called Quadralloy. Quadralloy will reduce wear between bearing race and axle surface. Call with model and year.

Make & Titanium Axles
Model Year

2007 R6
2007 R1

Front Axles - Specify Model and Year

Coated with Quadralloy                  
            
Yamaha R6 & R1 Rear Axles
  Mettec rear axle is forged and made with Titanium 6/4 at a strength level of Minimum UTS 160,000psi (1103MPa). Mettec applies our proprietary hard coating to the outside surface called Quadralloy. Quadralloy will reduce wear between bearing race and axle surface.
Make & Titanium Axles
Model Year

2007 R6
2007 R1

Rear Axles - Specify Model and Year

Coated with Quadralloy  

 

   
Yamaha R6 & R1 Swing Arm Pivots Shafts
   
Make & Swing Arm Pivots Shaft
Model  

2007 R6
2007 R1

Specify Year                                         
2007 Yamaha R1 Fastener Kits
  Mettec titanium bolt kits are very complete. We work hard at duplicating the OEM dimensions when appropriate and change the fasteners size wherever we can engineer a weight savings. The majority of Mettec fasteners have forged heads to increase fatigue strength. Mettec fasteners feature rolled threads. When you purchase all bolt kits, front axle, swing arm pivot shaft, and rear axles, you can reduce your bikes weight by 4.5 - 5.25 pounds (2.05 - 2.39 kilos) depending on model. 
  Available Kits
Front End Kit
Subframe Kit
Swing Arm Kit
Linkage Kit
Motor Kit
Rear Set Kit
Fairing Kit
Cosmetic Kit

                   Contact us for more information.                     
Yamaha R6 & R1 Swing Arm Pivots Shafts
   
Make &
Model  

2007 R6
2007 R1

Specify Year                                         
R1 Clutch Cover
Lightweight and flashy. These are our aluminum bolts. They come in red, black, blue pictured here, and gold. These really make the side of the bike jump out at you.
Make &  
Model  


2007 R1

                                        
R1 Gas Cap
These bolts are our button head bolts. They are shorter than normal allen head bolts, so they really sink back into the hole. This really gives the cap a larger look.
Make &
Model  


2007 R1

                                      
R1 Stator Cover
Lightweight and flashy. These are Mettec’s aluminum bolts. They come in red, black, blue pictured here, and gold. These are the finishing touch to make your bike stand out.
Make &
Model  


2007 R1

                                        
R6 Clutch Cover
Lightweight and flashy. These are our aluminum bolts. They come in red, black, blue, and gold pictured here. The finishing touch to give that personalized appearance.
Make & Swing Arm Pivots Shaft
Model  

2007 R6

                                     
R6 Shifter
Lightweight and flashy. These are our aluminum bolts. They come in red, black, blue, and gold pictured here. The finishing touch to all bikes big and small.
Make &
Model  

2007 R6

                                   
R6 2007 Cosmetic Kit
Here are all the bolts included in a cosmetic kit. The kit includes bolts for the side covers, windscreen, and the gas cap. The side cover bolts are being show in blue in this picture.
Make &
Model  

2007 R6

                                        
R6 2007 Motor Kit
These are most of the bolts for the motor kit. The missing bolts are the long motor mount bolts, which were too long to fit in the picture. The kit covers the valve cover, exhaust headers, radiator mounts, motor mounts, and general brackets.
Make &
Model  

2007 R6

                                      
R6 2007 Ti Front End Kit
These are the bolts that make up the front end kit. They include the triple clamps, axle pinch, brake calipers, lever pivots, control perches, brake rotors, and front nose subframe. One of the most noticeable kits that stand out and adds flash to your bike.
Make &
Model  

2007 R6

                                     
R6 2007 Ti Linkage Kit
All nut bolts and washers that hold the suspension in place. Top shock, lower shock, linkage through frame, linkage through swingarm, and linkage knuckle.
Make &
Model  

2007 R6

                                
R6 2007 Ti Rear Set Kit
These bolts are for your foot pegs. They include the bolts for the rear set mounts, brake pivot, master cylinder, swingarm guards, and some shift linkage.
Make &
Model  

2007 R6

                                    
R6 2007 Ti Subframe Kit
These are all the bolts that touch your subframe. They include the subframe mounts, passenger peg mounts, muffler mounts, seat bolts, and any braces.
Make &
Model  

2007 R6

                                      
R6 2007 Ti Swing Arm Kit
The bolts here are for the swingarm. This kit includes the bolts for brake rotor, brake caliper, sprocket, chain rubber, chain guard, tire hugger, and brake lines.
Make &
Model  

2007 R6

                                   

Quantity and OEM discounts available. 
Dealer inquiries are also welcome.